Technology of laying gypsum tiles along with your hands

  • -

Technology of laying gypsum tiles along with your hands

Category : laying

Gypsum tiles must be laid properly, as not just the aesthetic appearance of cosmetic facing, but in addition the service quality

of this substance will be dependent on the engineering of job. The product is more universal, and it can be connected to concrete,

plaster, brick or gypsum board sheets, and provided that the surface of the foundation is even and has no defects.

In the event the flaws of the base are important, it ought to be thoroughly treated with primer, and then a cement mortar is

created, which fills all of the cracks. Then the surface ought to be primed and dried. Primer treatment is necessary to improve

the bond between the tile and the walls. In this case, its composition should decide on a special, comprising components which

stop the appearance of fungus and mould.

In the modern interior of the rooms most often used gypsum tiles, even imitating natural stone or brick. To execute decorative

finishing your self, it is necessary first of all to pick a strategy of tile placement and prepare a remedy. It is crucial to

focus on the reverse side of this substance. If its surface has an embossed surface, then the glue ought to be placed using an

trowel, and if it is even, then with a notched one.

The tech of this job is masterfasada.ru as follows:

* A thin layer of glue is applied to the pre-prepared wall. It is distributed over the base so it is likely to place 4-5 tiles.

Decorative cladding may be put either on plasterboard, and on putty.

* Glue the back side of these tiles with adhesive.

* Plaster components are pushed against the walls and their place is adjusted. To align the seams, it is suggested to use

spacers.

* Finishing is performed in rows, each of which should be shifted by half a tile. Facing is carried out into the corners of the

room, and then immediately eliminate any remaining mortar at the joints.

Drying the walls requires no more than a day and needs a constant humidity and temperature in the room. The final stage in the

laying of gypsum tiles is the decor. To try it, the joints between the components are full of a special solution, the color of

which matches the brick.

Cosmetic fake of brickwork on the walls will be carried out in the following ways:

* Cutting on the plastered surface of the seams of masonry using a bolt cutter with your own hands;

* placing of tiles beneath the brick:

* imitating the format and colour of the side of one brick;

* Imitating a fragment of brickwork of many bricks.

The best way to decorate"under the brick" will be the one that enables you to create a functional coating with the most appearance

of its resemblance to organic masonry. All three strategies to conduct this type of finishing works meet the requirements, but the

cutting edge of joints using a bolt is more labor-intensive and the creation of considerable amounts of dust, and so let's

consider more ordinary ways.

The old finish is removed from the walls, and the outside, if needed, is leveled to get rid of the requirement to glue plaster on

a thick coating of adhesive.

Combining these cladding with other types of interior finishes can be both systematic and performed without any clear consistency,

chaotically, with imitation of signs of aging.

With the support of decorative gypsum tiles it's possible to imitate a lot of textures.

A large number of textures could be imitated with the support of decorative gypsum tiles.

The wall where it is to be installed should possess the following characteristics:

* Hardness and intensity of the surface;

* The absence of uneven places and sharp sections;

* not any deformations.

Decorative tiles at the interior of this kitchen

Walls are created from a variety of substances, so let's break down the individual rules of setup.

When dealing with concrete, there'll not be any big problems. It's only necessary to take into account the porosity of this

material. Concrete, that has nearly no pronounced pores, should be treated with a good primer.

Mounting gypsum tiles concrete

Before starting work on the installation of gypsum tiles in the walls, then it is worth checking the strength of the surface.

After the plaster does not drop off the wall and at precisely the same time holds nicely, it's possible to simply paint it using

primer.

Mount the tiles on the painted concrete shouldn't. The surface should be scratched, making sure to misfire, then it should be

grouted and covered with a coating of plaster.